Time to Hire: How to Calculate It and What's a Good Number
Find where a search lost time by comparing time to hire with time to fill, and check both against SHRM's benchmark

Time to hire is the number of days between a candidate entering your pipeline and that candidate accepting your offer.
It shows how quickly you move a person through once you have them. Pair it with time to fill, and you can show a hiring manager or client exactly where a slow search lost its days.
Key takeaways
- Time to hire covers only the hired candidate's time in process. Time to fill covers the whole search.
- Use both, because the gap between them shows whether delay sits before sourcing or inside your process.
- Report the median, not the average, since one stalled search can skew a small average by weeks.
- No reliable public benchmark exists for this metric, so set your own target from past hires.
What the metric means
The clock starts when the candidate applies, or when you source them and they agree to be considered. It stops the day they accept your offer.
Only the person you hired counts, so you're not averaging across every applicant, just the one who signed.
That matters because the number isolates the part of a search you control once a candidate shows up. Screening, interviews, feedback loops, and the offer step all sit inside it. Anything that happened before the candidate arrived sits outside.
How to calculate it
Subtract the date the hired candidate entered your pipeline from the date they accepted. Do that for every hire in a period, then take the median across them.
The formula for one hire: offer accepted date minus candidate entered pipeline date.
A worked example: a software engineer applies on March 3 and accepts on April 2, so that hire counts as 30 days. If you hired five engineers last quarter at 30, 24, 41, 28, and 95 days, your median is 30, and your average is 44. Report the median, since one stalled search pulled the average up by two weeks.
SHRM reports medians for the same reason, since outliers skew averages. The same logic applies to a cost per hire number: one outlier distorts a small sample.
Pull the dates from one place
Consistency matters more than precision here, so pick one source for each date and use it every time.
For the start date, use the day a candidate applied or the day a sourced candidate agreed to be considered. Don't use the day you first found their profile, because that adds time they never spent in your process.
For the end date, use the day the candidate accepted the offer in writing. A verbal yes can fall apart, and counting it early makes the number look better than it is.
For time to fill, take the day the requisition opened. If a role sits open before it's approved, note which date you use so quarters stay comparable.
Time to fill vs time to hire
Time to fill counts the days between when the requisition opens and when the offer is accepted. SHRM's benchmarking report uses calendar days, including weekends and holidays, as the standard definition.
It measures how long the seat stays empty, not how fast a specific candidate moved.
The clock starts earlier than the one for the inside number. It includes requisition approval, posting, and the sourcing stretch before any candidate enters your pipeline.
For in-house teams, that early stretch sits inside the company. For agency recruiters, part of it sits with the client.
| Measure | Starts when | Ends when | What it covers |
|---|---|---|---|
| Time to fill | Requisition opens | Offer accepted | All work including approval posting and sourcing |
| Time to hire | Hired candidate enters pipeline | Offer accepted | Only the hired candidate's time in your process |
If time to fill is 60 days and the inside number is 20, then 40 of those days happened before your eventual hire showed up. If both are 55, the delay sits inside your screening and decision steps.
This split matters most when you're reporting to a hiring manager who assumes a long search means a slow recruiter.
What the benchmarks show
No reliable public benchmark exists for the inside number. SHRM publishes time to fill, not the candidate-in-process figure. Treat any "average time to hire" figure with care, since it may be a time-to-fill number under a different label.
For time to fill, SHRM's 2025 benchmarking report found a median of about a month and a half for executive and nonexecutive roles. The survey included 2,371 U.S. recruiting executives. Executive roles dropped from 60 days in 2022 to 45 days in 2025. Extra-large employers, with 5,000 or more staff, reported 61 days for nonexecutive roles and 60 for executive roles.
Those extra-large employers also spend nearly twice as long on approval, posting, and interviews. Treat all of these as in-house employer figures. If you're an agency recruiter, your share of those days depends on how fast the client moves.
For context, SHRM's 2025 talent trends found that 69% of organizations are still struggling to fill roles.
Use the gap between the two numbers
Subtract the inside number from time to fill; the difference points to where a slow search burned days.
Three patterns are worth checking.
Wide gap, short inside number: delay sat before your hired candidate arrived. Likely culprits are requisition approval, slow posting, and a thin sourcing pool.
Narrow gap, both numbers high: delay sat inside your process. Culprits are screening, interview scheduling, feedback loops, and offer approval.
Both numbers high with a wide gap: you have both problems. Fix the earlier stretch first, because the later one can shrink once you have more candidates to compare.
Agency recruiters, bring this split into your next client meeting. If the client's approval chain ate three weeks before you started sourcing, the number that makes the search look slow is theirs, not yours. Sourcing metrics from your own pipeline back that up.
Shorten the stretch you own
Book a demoCheck what to show the hiring manager before the next review
Three numbers belong in your next recruiting review: the median for your closed hires, the median time to fill for the same roles, and the gap between them.
Walk the room through the gap when you present. If it's wide, name what's happening before candidates reach you.
How long do requisitions sit for approval? How long do roles go unposted? How shallow is the sourcing pool?
If the gap is narrow and both numbers are high, name what's happening inside. Look for scheduling delays, slow feedback, or a recruiting funnel that loses too many candidates between the first screen and the onsite.
This framing changes the conversation. The question stops being "why is hiring slow" and starts being "which part is slow, and whose part is it."
Start the next search with better candidate data
Book a demoFrequently asked questions
Is this the same as time to fill?
No. The inside number counts only the hired candidate's time in your pipeline. Time to fill counts the whole search, starting the day the requisition opened.
Should I report the average or the median?
Report the median, because one stalled search can skew a small average by weeks, which is why SHRM reports medians too.
What's a good benchmark?
No reliable public benchmark exists for this metric. SHRM publishes time to fill, not the inside number, so set your own target from your last four quarters of hires in the same role family.
Does the clock include the notice period?
No, the clock stops at offer accept, not at the candidate's start date.
Which number do I take to a hiring manager?
Both, with the gap between them. The gap tells the hiring manager whether delay sat with their approval and feedback or inside your screening.
About the author

Founder & CEO of Rotto, building tools that help tech recruiters source better candidates, faster.





